d398a6ced2
- CitrineOS core extracted (CSMS OCPP 2.0.1) - OpenOCPP extracted (firmware OCPP 1.6J/2.0.1) - ShapeShifter library installed (pip install -e) - ShapeShifter specification extracted - EVerest extracted TODO updated with progress
170 lines
3.6 KiB
YAML
170 lines
3.6 KiB
YAML
charge_bridge:
|
|
name: cb_sat_ac
|
|
ip: ANY_EVSE
|
|
fw_file: ./firmware/charge-bridge-fw_complete.cbfw
|
|
fw_update_on_start: true
|
|
mdns_name: ""
|
|
|
|
heartbeat:
|
|
interval_s: 1
|
|
connection_to_s: 10
|
|
|
|
safety:
|
|
pp_mode: "disabled"
|
|
cp_avg_ms: 10
|
|
inverted_emergency_input: 0
|
|
relay_1:
|
|
relay_mode: "PowerRelay"
|
|
# Auxilary contact is connected from the OMRON relay
|
|
feedback_enabled: true
|
|
# The Omron relay switches in less than 100ms, use 200ms here
|
|
feedback_delay_ms: 200
|
|
# Only for PCB version 1.1, set to false for PCB version 1.2 and up
|
|
feedback_inverted: true
|
|
# PWM not supported yet
|
|
pwm_dc: 100
|
|
pwm_delay_ms: 0
|
|
switchoff_delay_ms: 10
|
|
relay_2:
|
|
# Not connected on PCB
|
|
relay_mode: "UserRelay"
|
|
feedback_enabled: false
|
|
feedback_delay_ms: 10
|
|
feedback_inverted: false
|
|
pwm_dc: 100
|
|
pwm_delay_ms: 0
|
|
switchoff_delay_ms: 10
|
|
relay_3:
|
|
# Not connected on PCB
|
|
relay_mode: "UserRelay"
|
|
feedback_enabled: false
|
|
feedback_delay_ms: 10
|
|
feedback_inverted: false
|
|
pwm_dc: 100
|
|
pwm_delay_ms: 0
|
|
switchoff_delay_ms: 10
|
|
|
|
can_0:
|
|
enable: true
|
|
local: "cb_can"
|
|
baudrate: 250000
|
|
|
|
serial_1:
|
|
enable: true
|
|
local: "/dev/cb_uart"
|
|
baudrate: 115200
|
|
stopbits: OneStopBit
|
|
parity: None
|
|
|
|
serial_2:
|
|
enable: true
|
|
local: "/dev/cb_rs485"
|
|
baudrate: 9600
|
|
stopbits: OneStopBit
|
|
parity: None
|
|
|
|
plc:
|
|
enable: true
|
|
tap: "cb_plc"
|
|
ip: 172.25.6.1
|
|
netmask: 255.255.255.0
|
|
mtu: 1518
|
|
powersaving_mode: 1
|
|
|
|
evse_bsp:
|
|
enable: true
|
|
module_id: "cb_bsp"
|
|
mqtt_remote: "localhost"
|
|
mqtt_port: 1883
|
|
mqtt_bind: 127.0.0.1
|
|
mqtt_ping_interval_ms: 1000
|
|
capabilities:
|
|
max_current_A_import: 16
|
|
min_current_A_import: 6
|
|
max_phase_count_import: 3
|
|
min_phase_count_import: 3
|
|
max_current_A_export: 16
|
|
min_current_A_export: 6
|
|
max_phase_count_export: 3
|
|
min_phase_count_export: 3
|
|
supports_changing_phases_during_charging: false
|
|
connector_type: "IEC62196Type2Cable"
|
|
ovm_enabled: false
|
|
ovm_module_id: cb_ovm
|
|
|
|
gpio:
|
|
enable: true
|
|
interval_s: 1
|
|
mqtt_remote: "localhost"
|
|
mqtt_port: 1883
|
|
mqtt_bind: 127.0.0.1
|
|
mqtt_ping_interval_ms: 1000
|
|
gpio_0:
|
|
# RCD.TEST
|
|
#mode: "Rcd_Selftest_Output"
|
|
# Self test not fully supported yet
|
|
mode: "Input"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
# RCD self test duration (ignore emergency input signals for this time after self test)
|
|
# and show reason of safety decision on host somehow to simplify debugging
|
|
config: 1000
|
|
gpio_1:
|
|
# RCD.ERROR
|
|
mode: "Input"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
config: 0
|
|
gpio_2:
|
|
# MOTOR_1
|
|
# simple Motor lock with only 2 wires (no feedback contacts)
|
|
mode: "MotorLock_1"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
# 1000 ms motor drive time for locking/unlocking
|
|
config: 1000
|
|
gpio_3:
|
|
# MOTOR_2
|
|
# simple Motor lock with only 2 wires (no feedback contacts)
|
|
mode: "MotorLock_2"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
config: 1000
|
|
gpio_4:
|
|
# RCD.PWM
|
|
# not supported yet
|
|
mode: "Input"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
config: 0
|
|
gpio_5:
|
|
# External GPIO on connector J4 pin 9 (10kOhm I/O)
|
|
mode: "Input"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
config: 0
|
|
gpio_6:
|
|
# External GPIO on connector J4 pin 10 (10kOhm I/O)
|
|
mode: "Input"
|
|
pulls: "PullUp"
|
|
mdns: false
|
|
config: 0
|
|
gpio_7:
|
|
# External GPIO on connector J3 pin 11 (10kOhm I/O)
|
|
mode: "Input"
|
|
pulls: "NoPull"
|
|
mdns: false
|
|
config: 0
|
|
gpio_8:
|
|
# External GPIO on connector J3 pin 12 (10kOhm I/O)
|
|
mode: "Input"
|
|
pulls: "PullDown"
|
|
mdns: false
|
|
config: 0
|
|
gpio_9:
|
|
# Not connected
|
|
mode: "Input"
|
|
pulls: "PullDown"
|
|
mdns: false
|
|
config: 0
|